Find your fit.

Pick your tent brand.

Don't see yours? We add brands regularly.

You need Option .

Here's where to get it:

Frequently Asked Questions

Will the Slipstream fit my tent and rack?

Short answer: probably, but three things have to line up. Your tent has to run Option A, B, or C hardware (most do). Your crossbar has to sit inside 0.75"–3.3" wide and 0.75"–2.1" tall. You need at least 3.5" of clearance between the top of your crossbar and the roof.

We have 32 tent brands confirmed and most major rack brands on file — Thule, Yakima, Rhino Rack, Prinsu, Sherpa, Front Runner, RSI, Billie Bars, OEM 4Runner and Tacoma crossbars, and more. Full matrix at tentmount.com/pages/tent-and-rack-compatibility-for-quick-release-mounts.

Which option do I need — A, B, or C?

It's set by the hardware inside your tent's mounting rail, not by the tent brand alone. Easiest way: open the rail and look.

  • Aluminum square plate that slides in the channel → Option A. Most tents use this.
  • Narrow ~9mm slot with a wider plate sitting inside behind it → Option B. Intrepid, James Baroud, Autohome, GFC Superlite, Roof Space 2, Trustmade, Ironman Swift, Naturnest Polaris.
  • Bare M8 bolt with a 13mm hex head, no plate at all → Option C. Inspired Overland, some Ironman, some older 23Zero Kabari/Armadillo, some Freespirit.

Not sure? Snap a photo of the inside of the rail and the original hardware and send it to sales@starksidegear.com. Photos are the fastest way — we answer these same-day.

Can I reach my crossbars to operate the mounts?

This is the question that matters most and the one most people skip. The Slipstream gets tightened and released from underneath the tent. You need to reach in with your wrist to the front AND rear crossbars, on both sides of the truck.

Racks that usually block this: Prinsu, Sherpa, TrailRax, Wescott, Cali Raised — anything with side plates. Front Runner Slimline II works with a rotation fit kit. OEM factory crossbars on a 4Runner or Tacoma? Usually fine. Front Runner flat platforms? Usually fine if the bars sit proud of the deck.

If you can't get your wrist to the crossbar, the Slipstream is wrong for you.

How much clearance do I need?

3.5 inches minimum for a standard setup with a hand knob. The long edge of a credit card is almost exactly 3.5" — slide one between the top of your crossbar and the roof. If it fits, you're in.

The full chart:

  • Standard + hand knob: 3.5" minimum clearance
  • Standard + wing nut: 3.0" minimum clearance
  • Tall crossbar (1.6"–2.1") + hand knob: 4.0" minimum clearance
  • Tall crossbar + wing nut: 3.5" minimum clearance

If you're right at the edge, swap the hand knob for the included wing nut and you get a half-inch back. If you're below 3.0", the Slipstream isn't the right tool.

Will the Slipstream work with my Prinsu, Sherpa, or Front Runner rack?

Depends on one thing: can you reach your wrist to the crossbars from underneath?

Prinsu and Sherpa: The mount clamps those bars fine — access is what stops people. Reaching the front mounts on a 4Runner is the specific failure, and it has driven more returns than any other setup. If your rack has side plates, assume no. Before you buy, do the wrist test on the front crossbar and email us photos of your rack.

Front Runner Slimline II: Works with the 1230 Wide Crossbar Fit Kit plus a rotation kit. The rotation kit lets the mount drop between slats. Kit prices on the product page.

Front Runner SlimSport: Works with the rotation fit kit.

Full rack matrix at tentmount.com/pages/tent-and-rack-compatibility-for-quick-release-mounts.

Will the Slipstream work with my OEM or factory rack?

Usually yes, if the crossbars are actual crossbars and not just rails. Toyota 4Runner and Tacoma factory crossbars (~2.0" × 0.75") are compatible and clearance is normally fine. Subaru Outback OEM crossbars work for most customers.

What kills an OEM rack for the Slipstream: crossbars taller than 2.1" (Rough Country adjustable bars are 3.25" — not compatible), clearance under 3.5", or a rack with no real crossbar at all — just a flat deck.

Do your mounts work with Gobi or other no-clearance racks?

Gobi racks — no. The slat design doesn't leave room for the Slipstream's clamp to seat properly, and clearance under the tent is too tight. We'll save you the return: email sales@starksidegear.com before ordering and we'll confirm your specific Gobi setup.

Other slat-only or low-clearance racks (Prinsu, Sherpa, TrailRax, UpTop, Wescott, Front Runner Slimline II): some work with a rotation fit kit, some don't. The access test is simple — can you reach your wrist between the tent and the rack to the crossbar? If yes, the Slipstream usually works. If no, email us before you order and we'll tell you straight whether it is worth trying.